Tool:BambuLab P1S (3D printer) - Bewerkingsoverzicht

H.Acker: added open source software alternative (OrcaSlicer Bambu lab)

2026-08-31T17:55:51Z

added open source software alternative (OrcaSlicer Bambu lab)

@@ Regel 8: / Regel 8: @@
 Then, connect to the BambuWifi. Ask someone for the password.
 When connected to the BambuWifi, the printer should be shown at the 'Device' tab. Click on the device and it asks you for the access code. This code can be found on the printer itself. Use the arrow keys next to the screen on the printer to navigate to Settings > WLAN > Access Code. Use this access code to connect your pc to the printer.
 === Set up project ===
-In the 'Prepare' tab, place your 3d file and position it on the plate. Slice it (or click the 'Preview' tab), and you will see the estimated time and other stats. You can now send it to the printer.
+In the 'Prepare' tab, place your 3D file and position it on the plate. Select the filament you want to use (it can be necessary(?) to go to the "Device" tab and connect to the printer and load the right filament first). Slice it (or click the 'Preview' tab), and you will see the estimated time and other stats. You can now send it to the printer.
 === After printing ===

Sjors Gielen op 23 jul 2025 om 11:29

2025-07-23T11:29:14Z

← Oudere versie		Versie van 23 jul 2025 11:29
Regel 13:		Regel 13:

	=== After printing ===		=== After printing ===
	The printer always prints some exess filament on the bottom side of the plate. Please remove this after printing.		The mat attaches to the print bed magnetically. It takes a little bit of force to pull off the mat from the print bed, it's easiest to start in a corner.

			The printer always prints some exess filament on the bottom side of the plate. Please remove this after printing. Also, it's appreciated if you clean the mat with a little bit of bio-ethanol after your print.

	=== Costs ===		=== Costs ===

Sjors Gielen op 22 jul 2025 om 21:18

2025-07-22T21:18:17Z

← Oudere versie		Versie van 22 jul 2025 21:18
Regel 16:		Regel 16:

	=== Costs ===		=== Costs ===
	You only pay for the filament. In the 'Preview' tab you see the amount of grams of filament your print will use. The costs are €0,03 per gram. You can transfer the costs to the account `3d-printer` on RevBank.		You only pay for the filament. In the 'Preview' tab you see the amount of grams of filament your print will use. The costs are €0,03 per gram.

			You can transfer the costs to the account `3d-printer` on RevBank. Use `give 3D-printer <amount>`, e.g. `give 3D-printer 6` if you printed 200 grams. Then, the next command is your username.

Jay9: correct price

2025-07-22T21:00:30Z

correct price

← Oudere versie		Versie van 22 jul 2025 21:00
Regel 16:		Regel 16:

	=== Costs ===		=== Costs ===
	You only pay for the filament. In the 'Preview' tab you see the amount of grams of filament your print will use. The costs are €0,35 per gram. You can transfer the costs to the 3d-printer ~~account~~ on RevBank.		You only pay for the filament. In the 'Preview' tab you see the amount of grams of filament your print will use. The costs are €0,03 per gram. You can transfer the costs to the account `3d-printer` on RevBank.

Jay9: add plate

2025-06-19T17:29:23Z

add plate

← Oudere versie		Versie van 19 jun 2025 17:29
Regel 1:		Regel 1:
	We have a BambuLab P1S 3D printer.		We have a BambuLab P1S 3D printer.
	We have a 0.4 mm nozzle, different PET-G and PLA filaments, ~~and~~ a Bambu Textured PEI plate.		We have a 0.4 mm nozzle, different PET-G and PLA filaments, a Bambu Textured PEI plate and Bambu Smooth PEI plate.

	=== Software ===		=== Software ===

Jay9: layout

2025-06-19T08:33:42Z

layout

← Oudere versie		Versie van 19 jun 2025 08:33
Regel 2:		Regel 2:
	We have a 0.4 mm nozzle, different PET-G and PLA filaments, and a Bambu Textured PEI plate.		We have a 0.4 mm nozzle, different PET-G and PLA filaments, and a Bambu Textured PEI plate.

	~~# software~~		=== Software ===
	To use this printer, you need the Bambu Studio software. This can be downloaded here:		To use this printer, you need the Bambu Studio software. This can be downloaded here:
	https://bambulab.com/en-eu/download/studio (free, Windows and Mac only)		https://bambulab.com/en-eu/download/studio (free, Windows and Mac only)
Regel 9:		Regel 9:
	When connected to the BambuWifi, the printer should be shown at the 'Device' tab. Click on the device and it asks you for the access code. This code can be found on the printer itself. Use the arrow keys next to the screen on the printer to navigate to Settings > WLAN > Access Code. Use this access code to connect your pc to the printer.		When connected to the BambuWifi, the printer should be shown at the 'Device' tab. Click on the device and it asks you for the access code. This code can be found on the printer itself. Use the arrow keys next to the screen on the printer to navigate to Settings > WLAN > Access Code. Use this access code to connect your pc to the printer.

	~~# set~~ up project		=== Set up project ===
	In the 'Prepare' tab, place your 3d file and position it on the plate. Slice it (or click the 'Preview' tab), and you will see the estimated time and other stats. You can now send it to the printer.		In the 'Prepare' tab, place your 3d file and position it on the plate. Slice it (or click the 'Preview' tab), and you will see the estimated time and other stats. You can now send it to the printer.

	~~# after~~ printing		=== After printing ===
	The printer always prints some exess filament on the bottom side of the plate. Please remove this after printing.		The printer always prints some exess filament on the bottom side of the plate. Please remove this after printing.

	~~# costs~~		=== Costs ===
	You only pay for the filament. In the 'Preview' tab you see the amount of grams of filament your print will use. The costs are €0,35 per gram. You can transfer the costs to the 3d-printer account on RevBank.		You only pay for the filament. In the 'Preview' tab you see the amount of grams of filament your print will use. The costs are €0,35 per gram. You can transfer the costs to the 3d-printer account on RevBank.

Jay9: first draft

2025-06-19T08:32:17Z

first draft

Nieuwe pagina

We have a BambuLab P1S 3D printer.
We have a 0.4 mm nozzle, different PET-G and PLA filaments, and a Bambu Textured PEI plate.

# software
To use this printer, you need the Bambu Studio software. This can be downloaded here:
https://bambulab.com/en-eu/download/studio (free, Windows and Mac only)
You need to create a (free) account, and log in.
Then, connect to the BambuWifi. Ask someone for the password.
When connected to the BambuWifi, the printer should be shown at the 'Device' tab. Click on the device and it asks you for the access code. This code can be found on the printer itself. Use the arrow keys next to the screen on the printer to navigate to Settings > WLAN > Access Code. Use this access code to connect your pc to the printer.

# set up project
In the 'Prepare' tab, place your 3d file and position it on the plate. Slice it (or click the 'Preview' tab), and you will see the estimated time and other stats. You can now send it to the printer.

# after printing
The printer always prints some exess filament on the bottom side of the plate. Please remove this after printing.

# costs
You only pay for the filament. In the 'Preview' tab you see the amount of grams of filament your print will use. The costs are €0,35 per gram. You can transfer the costs to the 3d-printer account on RevBank.