Projects:Delta printer: verschil tussen versies

Uit Hackerspace Nijmegen Wiki
Naar navigatie springen Naar zoeken springen
Geen bewerkingssamenvatting
Geen bewerkingssamenvatting
Regel 9: Regel 9:
=Software=
=Software=
Using [https://www.pronterface.com/ proterface], we discovered the original firmware:
Using [https://www.pronterface.com/ proterface], we discovered the original firmware:
{|
{| class="wikitable"
|+
!Old software
|-
|-
! scope="col" |COLUMN1
|echo:Marlin1.0.0
|-
echo: Last Updated: Sep 20 2016 17:01:22 | Author: (Kossel KOSSEL)
|ROW1
 
|-
Compiled: Sep 20 2016
|ROW2
 
echo: Free Memory: 3738  PlannerBufferBytes: 1232
 
echo:Hardcoded Default Settings Loaded
 
echo:Steps per unit:
 
echo:  M92 X100.00 Y100.00 Z100.00 E150.00
 
echo:Maximum feedrates (mm/s):
 
echo:  M203 X200.00 Y200.00 Z200.00 E200.00
 
echo:Maximum Acceleration (mm/s2):
 
echo:  M201 X3000 Y3000 Z3000 E3000
 
echo:Acceleration: S=acceleration, T=retract acceleration
 
echo:  M204 S3000.00 T3000.00
 
echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s),  Z=maximum Z jerk (mm/s),  E=maximum E jerk (mm/s)
 
echo:  M205 S0.00 T0.00 B20000 X20.00 Z20.00 E20.00
 
echo:Home offset (mm):
 
echo:  M206 X0.00 Y0.00 Z0.00
 
echo:Endstop adjustement (mm):
 
echo:  M666 X0.00 Y0.00 Z0.00
 
echo:PID settings:
 
echo:   M301 P22.20 I1.08 D114.00
|}
|}



Versie van 13 okt 2024 14:02

We got donated a FLSUN Delta Kossel. It has a mks base v1.5 board.

Hardware

Stepper motors: SL42STH40-1684A Controller: mks base v1.5 board Power supply: S-200-12 with 12V 16.7A output

Software

Using proterface, we discovered the original firmware:

Old software
echo:Marlin1.0.0

echo: Last Updated: Sep 20 2016 17:01:22 | Author: (Kossel KOSSEL)

Compiled: Sep 20 2016

echo: Free Memory: 3738  PlannerBufferBytes: 1232

echo:Hardcoded Default Settings Loaded

echo:Steps per unit:

echo:  M92 X100.00 Y100.00 Z100.00 E150.00

echo:Maximum feedrates (mm/s):

echo:  M203 X200.00 Y200.00 Z200.00 E200.00

echo:Maximum Acceleration (mm/s2):

echo:  M201 X3000 Y3000 Z3000 E3000

echo:Acceleration: S=acceleration, T=retract acceleration

echo:  M204 S3000.00 T3000.00

echo:Advanced variables: S=Min feedrate (mm/s), T=Min travel feedrate (mm/s), B=minimum segment time (ms), X=maximum XY jerk (mm/s),  Z=maximum Z jerk (mm/s),  E=maximum E jerk (mm/s)

echo:  M205 S0.00 T0.00 B20000 X20.00 Z20.00 E20.00

echo:Home offset (mm):

echo:  M206 X0.00 Y0.00 Z0.00

echo:Endstop adjustement (mm):

echo:  M666 X0.00 Y0.00 Z0.00

echo:PID settings:

echo:   M301 P22.20 I1.08 D114.00


Link list

https://www.3dprintersbay.com/flsun-autolevelling-kossel-diy-kit

https://www.youtube.com/watch?v=lOb5BuwkcNI

Todo:

  1. Install the firmware using the following tutorial (interesting bit starts at 5:00 mark), calculator is at https://rev22.github.io/RepRapCalculator/#MotorStuffSPMB
  2. Setup calibration using the auto calibration feature: https://marlinfw.org/docs/gcode/G033.html
  3. profit!?