Tool:Ultimaker 2 (3D printer): verschil tussen versies

Uit Hackerspace Nijmegen Wiki
Naar navigatie springen Naar zoeken springen
k (Minnozz heeft pagina Tool:Ultimaker 2 (3D printer) hernoemd naar Tools:Ultimaker 2 (3D printer): Use Tools: prefix instead of Tool:)
(Added settings)
 
(2 tussenliggende versies door een andere gebruiker niet weergegeven)
Regel 1: Regel 1:
[[Bestand:Ultimaker-2.jpeg|x400px|right]]
We have an Ultimaker 2 3D printer at the space.
We have an Ultimaker 2 3D printer at the space.
It has an octoprint connected to it, login can be requested.
Some settings that are needed in cura to make a good print:
It is an ultimaker 2, but after setting is to ultimaker 2, change these settings to print via octoprint:
G-code flavor "Marlin"
Start G-code:
G21 ;metric values
G90 ;absolute positioning
M82 ;set extruder to absolute mode
M107 ;start with the fan off
G28 Z0 ;move Z to bottom endstops
G28 X0 Y0 ;move X/Y to endstops
G1 X15 Y0 F4000 ;move X/Y to front of printer
G1 Z15.0 F9000 ;move the platform to 15mm
G92 E0 ;zero the extruded length
G1 F200 E10 ;extrude 10 mm of feed stock
G92 E0 ;zero the extruded length again
G1 Y50 F9000
;Put printing message on LCD screen
M117 Printing...
End G-code
M104 S0 ;extruder heater off
M140 S0 ;heated bed heater off (if you have it)
G91 ;relative positioning
G1 E-1 F300  ;retract the filament a bit before lifting the nozzle, to release some of the pressure
G1 Z+0.5 E-5 X-20 Y-20 F9000 ;move Z up a bit and retract filament even more
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
M84 ;steppers off
G90 ;absolute positioning
;Version _2.6 of the firmware can abort the print too early if the file ends
;too soon. However if the file hasn't ended yet because there are comments at
;the end of the file, it won't abort yet. Therefore we have to put at least 512
;bytes at the end of the g-code so that the file is not yet finished by the
;time that the motion planner gets flushed. With firmware version _3.3 this
;should be fixed, so this comment wouldn't be necessary any more. Now we have
;to pad this text to make precisely 512 bytes.

Huidige versie van 16 mrt 2023 om 14:30

Ultimaker-2.jpeg

We have an Ultimaker 2 3D printer at the space.

It has an octoprint connected to it, login can be requested.


Some settings that are needed in cura to make a good print:

It is an ultimaker 2, but after setting is to ultimaker 2, change these settings to print via octoprint:


G-code flavor "Marlin"


Start G-code:

G21 ;metric values
G90 ;absolute positioning
M82 ;set extruder to absolute mode
M107 ;start with the fan off
G28 Z0 ;move Z to bottom endstops
G28 X0 Y0 ;move X/Y to endstops
G1 X15 Y0 F4000 ;move X/Y to front of printer
G1 Z15.0 F9000 ;move the platform to 15mm
G92 E0 ;zero the extruded length
G1 F200 E10 ;extrude 10 mm of feed stock
G92 E0 ;zero the extruded length again
G1 Y50 F9000
;Put printing message on LCD screen
M117 Printing...

End G-code

M104 S0 ;extruder heater off
M140 S0 ;heated bed heater off (if you have it)
G91 ;relative positioning
G1 E-1 F300  ;retract the filament a bit before lifting the nozzle, to release some of the pressure
G1 Z+0.5 E-5 X-20 Y-20 F9000 ;move Z up a bit and retract filament even more
G28 X0 Y0 ;move X/Y to min endstops, so the head is out of the way
M84 ;steppers off
G90 ;absolute positioning
;Version _2.6 of the firmware can abort the print too early if the file ends
;too soon. However if the file hasn't ended yet because there are comments at
;the end of the file, it won't abort yet. Therefore we have to put at least 512
;bytes at the end of the g-code so that the file is not yet finished by the
;time that the motion planner gets flushed. With firmware version _3.3 this
;should be fixed, so this comment wouldn't be necessary any more. Now we have
;to pad this text to make precisely 512 bytes.